A leaking radiator valve usually drips from one of three places: the spindle at the top, the nut joining the valve to the radiator, or the nut where it meets the pipe. Most leaks are slow and can be contained with a towel and a bowl while you arrange a repair. Turning both valves off isolates the radiator and stops the drip in many cases. Keep an eye on your boiler pressure, as even a small leak can drain it. Our plumbers in Binfield, Bracknell and the surrounding area can repair or replace the valve.

Find where the leak is coming from

Dry the valve with tissue, then wait and watch where the first drop forms. That tells you what’s wrong.

  • From the spindle, under the cap or TRV head. The gland packing around the spindle has worn. Common on older valves that have been turned a lot.
  • From the nut between the valve and the radiator. The radiator tail or its seal has failed, or the nut has worked loose.
  • From the nut on the pipe below. The compression joint where the valve meets the pipework is weeping.
  • From the valve body itself. A crack or corrosion. The valve needs replacing.

Sometimes water runs down from higher up, such as a bleed valve or a pinhole in the radiator, and collects at the valve. Check above before blaming the valve.

Safe things you can do now

  • Catch the water. Put a towel and a shallow tray or bowl under the valve to protect floors and ceilings below.
  • Isolate the radiator. Turn the TRV or control valve fully off. Then pull the plastic cap off the lockshield at the other end and turn it clockwise with a spanner or lockshield key until it stops. Count the turns so a plumber can reset it later.
  • Turn the heating off if the leak is from a joint and seems to get worse when the system is hot.
  • Check the boiler pressure. If it’s dropping, our guide to boiler pressure loss explains how topping up works on most systems.

Some people gently nip up a nut a fraction of a turn. If you try that, go carefully, hold the valve body steady with a second spanner and stop if it doesn’t help. Overtightening can split an olive or crack a fitting and turn a drip into a flood. Don’t undo any nuts with the system full.

What a plumber will do

Depending on the cause, the fix might be:

  • Repacking or replacing the spindle gland on the valve
  • Remaking the joint with a new olive or sealing the radiator tail
  • Replacing the whole valve, which often means draining the radiator or using a freezer kit on the pipe
  • Draining down part of the system and refilling it with inhibitor afterwards

If several valves are old and weeping, it can make sense to replace them together. Our guide to what a radiator valve is explains the different types, from manual and lockshield valves to TRVs.

When it’s more urgent

Call straight away if water is spraying rather than dripping, a ceiling below is stained or sagging, the leak is near electrics, or the boiler pressure keeps dropping to zero. If water is getting near sockets or light fittings, turn off the electricity at the consumer unit if you can do so safely.

Leaking radiators in Ascot and Binfield homes

Older houses around Ascot and Binfield often still have their original radiator valves, sometimes decades old, and these tend to start weeping when the heating comes back on in autumn. Hard water and sludge in older systems don’t help. If your radiators also heat unevenly or the system is full of black water, it may be worth looking at a wider central heating upgrade rather than fixing one valve at a time.

Frequently asked questions

Can I still use the heating with a leaking radiator valve?

Usually, if the leak is a slow drip, you can isolate that radiator and run the rest of the heating while you wait for a repair. Keep an eye on the boiler pressure. If it keeps dropping or the leak gets worse when the system heats up, turn the heating off and get it repaired.

Why does my radiator valve only leak when the heating is on?

Metal parts expand as they warm up, and a worn gland or tired joint can open just enough to let water through when hot. When the system cools, it seals again. That makes it easy to ignore, but it’ll usually get worse over time, so it’s best to get it fixed before winter.

How long does it take to replace a radiator valve?

For a straightforward swap, often around an hour, depending on access and whether the radiator needs draining. If the pipework is corroded or the valve is an unusual size, it can take longer. Replacing several valves in one visit is usually more efficient than separate call-outs.

Got a leaking radiator?

If one of your radiator valves has started dripping, give us a call on 01344 919 956 or drop us a message and we’ll get it fixed before it damages your floors.